Introduction
Even the nicest rifle scope in the world must be mounted properly to function as designed. And as rifle scopes have advanced, so too have the devices we use to mount them to our rifles. An unprecedented selection of options are available to today’s sharpshooter, and today we will be taking a look at one. Area 419 is well known in the precision rifle community for manufacturing many high quality shooting products. Today’s subject is Area 419’s Tactical one-piece scope mount.
Scope Mounts
Some out there might be asking; why a one-piece scope mount over rings? It’s not a bad question, and I’ll give you my answer. A one-piece scope mount is much more rigid than a pair of scope rings. It better holds your scope in a solid position on the rifle. Added benefits are things like built in cant, and greater clamping surface on both scope and rifle interface. And perhaps one of my favorite benefits, is the ability to easily swap scopes between one rifle to another.
Un-Boxing Area 419 scope mounts
As per usual, Area 419 products come in incredibly nice packaging. These scope mounts came in a waterproof locked hard-case, much like you’d store your rifle in if it was 6 inches long. Inside the foam lined case was the scope mount, the appropriate tools needed to install it, loctite to apply to fasteners, and enough instructional material for even a chimp to mount it properly.
The mount itself also looked immaculate. I really like the machined finished surface, and high quality coating. Even more so I like the large fasteners, something I wish more optic mounts would use. I was curious why the inside of the rings was raw aluminum, more on that later.
I looked at the base, and at first it seemed like perhaps the picatinny clamps could have been spread out a little bit more. But the more I looked at it, the less of a concern it became.
I must say, this thing looks extremely robust. Large screws holding down caps, and additionally secured and aligned by stainless dowel pins. Which I thought was an exceptional touch. The overall initial impression of these mounts was absolutely top notch.
Rifle Scope Installation
After playing around with these mounts for a bit, it was time to put them to work. I had a couple different ideas as far as where to use them. The first one would be on one of my heavy precision rifles, the Desert Tech SRS M2 in 338LM. I mounted a US Optics FDN25X in one of the Area 419 one-piece scope mounts, and because I’m a gear queer I added the diving board as well. The diving board attaches to the front scope ring cap, and serves as a mounting position for additional accessories. The Vortex Impact 4000 for example mounted up nicely on top of the scope, and would be right at home there. You can also mount a Wilcox Raptar fire control system with mounting holes made specifically for that device.
As I mounted various scopes in the Area 419 one piece scope mounts, I quickly found out why the rings remained raw inside. If I remember correctly I was told by the manufacturer that the rings are finish machined last, for a perfectly round cut for better holding of your scope. The raw aluminum additionally creates and incredibly cohesive grip on the scope tube. So much in fact that several times while mounting scopes I found myself cursing it.
When leveling a scope in the rings, we are all used to snugging the screws down while keeping the scope level. But the grip of the Area 419 rings is so impressive that even with minimal screw tension it was very difficult to move the scope. The rings grab the scope so well that even without the scope caps installed it is hard to move the scope in the mount. I can’t imagine how strong the grip must be once the rings are torqued down.
Accessory Mounting
Mounting accessories to the top of the ring cap is easy. There are two Torx screws to attach either a short pic rail section, a diving board, or one of the other accessory options. I mounted both of the options mentioned. The picatinny section is easy as can be, whereas the diving board was a touch more sensitive. The screws are captured within the diving board itself, using internal snap rings. And it is mounted using a tapered boss patented by Area 419. This requires the screws to be tightened equally as the diving board seats to the ring cap, and removed in the same fashion. Pushing the diving board up against the snap rings as the screws are loosened.
Other accessories can be mounted to the smaller screw receptacles. Area 419 makes level indicators, red dot mounts and other accessory mounts that easy screw into the side of the scope mount.
Rifle Interface
I mentioned at first that I thought maybe the picatinny clamps could have been placed wider. Maybe I’m mistaken but I like the idea of having as broad and integral mounting surface as I can. Close inspection of the picatinny clamps on the Area 419 mounts show more than enough clamping pressure and surface. Part of me thinks the bottom of the scope mount should have reciprocal picatinny teeth to better engage the rifle. But I’m also pretty sure the Area 419 engineers would have an explanation as to why they didn’t need such a feature. For such a well thought out device, I find it hard to believe they didn’t think through that idea and eliminate it.
I also found when mounting scopes to rifles that the picatinny clamp screws were a touch shorter than I would have liked. Perhaps this was done as a weight reducing measure, or to simplify the mounting. But on several different firearms I found that I had to basically remove the screws before I could get the mount onto the rifle’s pic rail. Maybe they are designed to be that way, but even if they aren’t I find it to be a very minor inconvenience.
Once attached, it is very obvious how well these mounts work. The ability to add or remove accessories to your optic mount is easily done. And with such precise manufacturing, zero’s are easily maintained even when removing and reinstalling them.
Final Thoughts
Having used the Area 419 one piece scope mounts on several different rifles now and mounting an assortment of scopes in them, I’ve gotten a good feel for them. Rifles chambered in 338 Lapua magnum, 7mm PRC, 308 Winchester and even 223 Remington. They are another outstanding product from the good folks at Area 419, and certainly worthy of their place in the niche market of high-end precision riflery. While they are not inexpensive, they are well within their asking price for $330. Other competitors like MPA offer similar robust design for less, but with less modularity as well. You can also find other options with equivalent strength and modularity from manufacturers like Sphur , albeit for significantly more money.
Like most products I have experienced from Area 419, you simply cannot go wrong with the products or service offered. If you are looking for a quality mount for your darling new precision rifle scope, look very hard at these before passing on them.
-CBM
