Being a sucker for nice optics, I enjoy exceptional riflescopes from both American and European manufacturers. But I really want to buy American-made optics as much as I can.

Burris is a well-known American optics manufacturer that has recently teamed up with optics stalwart Steiner Optics. Being a fan of both, I was excited to review the new Burris Veracity PH 4-20X50.

The Veracity is Burris’s premier hunting scope line, and the PH model is at the top of that line.

The Veracity PH incorporates Burris’s PĒK elevation turret, an electronic programmable and mechanical hybrid adjustment turret. Housed inside the 30mm tube of the PH, you will also find a digital Heads-up-display (HUD) that gives you all the information as you look through the scope.

The reticle is in the first focal plane, which always represents the indicated values regardless of magnification.
A traditional side-focus/parallax adjustment is on the scope’s left side; on the right, you will find a capped windage knob. Since hunters typically utilize the MOA scale instead of the MRAD one, it makes sense to have built the Veracity PH in MOA.

The reticle inside the Veracity was built for holding wind corrections with graduated windage marks.

The Veracity PH promises to give hunters a rapid and accurate firing solution for long-range hunting scenarios. Often when pursuing animals, there is little time to make corrections for distance. The PH allows users to use either MOA come-ups or have the actual distance shown rapidly in the internal HUD.

I can think of several scenarios over the past couple decades of hunting where that would have been very helpful. Hunting open country and long-range has been my bread and butter for at least that long, so I figured it would be a good place to put this scope to the test.

My initial impressions of the Veracity PH are pretty positive, it looks good, feels solid, and the optical quality seemed on par for its price.

I was pleased with the simplicity of the Bluetooth intercourse and integration with the Burris Connect app used to control the Veracity PH.

As a hunting scope for long-range hunters, the Veracity PH provides fast information for making quick shots.

Technology like rangefinders and ballistic computers have greatly increased the potential for making longer shots with predictability. The Burris Veracity PH was made to capitalize on those advances, and bring some of this technology aboard your riflescope.

With uploadable ballistic profiles, you can put the data right into your scope. These profiles carry bullet drop and windage deflection rates.

This is necessary when making longer shots to correct for distance and atmospheric changes around you. Having this data in your scope is a great advantage for long-range hunters in wide-open country.

If you are more of a bean-field hunter, where shots may not exceed two to three hundred yards, it’s probably more of a novelty than a necessity.

SPECIFICATIONS

I’ve had a few experiences with Burris optics over the years, and they have all been good ones. So I was eager to open up the Veracity PH package and get it into shooting condition as soon as possible.

My plan was to replace the Steiner T6X that I was currently running on my Desert Tech SRS M2. It is essentially the big brother to the Veracity, made in the same Colorado factory.

I mounted the Veracity in a Nightforce scope mount and leveled it on the rifle. It was during this process that I discovered one of the technological gadgets on the Burris scope; the internal level was not showing level compared to my bubble level, or my eye for that matter.

I assumed something was wrong, but after booting up the Burris connect app, I found the calibration procedure for the internal bubble level. You can zero the level on the scope physically using traditional procedures and then zero the internal digital level.

Before I’d even done that, I of course installed the two CR2450 lithium batteries that power the Veracity by loosening the battery cap on the side of the scope.

With the scope leveled and torqued down, I bore-sighted it looking out the window at the mountains above. Like most scopes, the PH turrets have three allen screws around the top to loosen the turret and reset them back to zero after getting the rifle sighted in.

I appreciated the capped windage turret since I rarely dial wind; I prefer to hold it instead. The Wind MOA reticle inside the scope was perfect for that.

Once I was on my range, I fired a few shots to adjust the zero of the rifle, and then it was time to see how this thing performed.

Before leaving the house, I had downloaded the ballistic profile of the ammunition I planned on shooting. It was easily added to the PH’s heads-up display, and using the app, I could select to have the HUD show either the actual MOA correction or the equivalent distance to the MOA dialed.

Again this seems like a very handy tool for hunters since you can upload your data, and after proofing it with the scope, it’s as easy as dialing the distance.

I’m not always a fan of “just dial the number” systems such as caliber/ballistic custom turrets because, typically, they do not allow for atmospheric changes and other common variations. The Veracity PH system, however, when used with the Connect App, allows you to update density altitude (DA) and other important factors to increase the accuracy of the firing solution.

It was time to stretch the rifle and scope combo out and see how all this tech lined up in an actual shot. The first thing I noticed when dialing the scope out for a longer shot was how stiff the elevation turret was.

I might have blamed it on the extreme cold that day, but it was just as stiff sitting on my kitchen table earlier that morning. I guess you could consider this a positive in some ways because the turret is unlikely to get accidentally turned before you make a shot. But even if it did, as you looked through the scope to make the shot, you could see if the elevation had been moved via the HUD inside.

I also noticed, to my surprise, that there were no clicks on the turret, a feature so common on riflescopes that it startled me. But due to the 1/10 MOA sensitivity of the turret, the clicks are unnecessary. You can see either on the turret housing or by the HUD inside what the turret is set to.

The focus/parallax adjustment on the side of the scope on the other hand is very smooth and easy to adjust. The variable 4-20 power magnification is an excellent choice for hunting and long-range hunting in my opinion, allowing for close up shots under one hundred yards or long shots as far as you have the skill to make.

Twenty power magnification is plenty for making shots as far as a thousand yards in my opinion, and it wasn’t long before we were doing just that with the Veracity PH.

The magnification adjustment ring was also easy to adjust, adding to my ability to zoom out to find targets, and right back in to engage them. With the scoped zoomed out to the four power setting, the reticle detail became quite fine, almost fine enough to lose its value.

Not a huge concern in my opinion because chances are if you are shooting at an animal at four power, it is likely going to be quite close and won’t require using reticle subtensions. The tapered reticle posts that thin as they approach the center also create a very natural point of aim that also reduces the importance of the center reticle details.

We fired a bunch of shots that afternoon, closely mimicking the same kinds of shots we would have taken on deer in these very same canyons. The Veracity PH made it very easy to move from one target to the next, and not much was getting away from me at that point.

Click here to continue reading