Its not every day that I get to write about a cartridge that I remember coming out, but today is one of those. It was twenty something years ago, I was a much younger fella recently married and a son on the way when I first learned about the 6.5 Grendel. Even back then 6.5’s were hot, so when I heard about the 6.5 Grendel I paid attention.
The little Grendel came from Alexander Arms, and the whole idea was to put higher Ballistic Coefficient (BC) bullets into an AR-15. Bumping up the case size was also necessary in order to get these 6.5 Bullets up to a respectable speed. All this to create a cartridge that would make the AR-15 more lethal at distances beyond 500 yards or more.
The popularity of the Grendel has led to similar cartridges gaining fame as well. The 6 ARC has become extremely popular for similar reasons, and now the 22 ARC is following its footsteps.
22 ARC, 6 ARC, and the 6.5 Grendel
6.5 Grendel Dimensions
The 6.5 Grendel inherited a similar volume from it PPC/220 Russian parent case, the case volume is approximately 35 grains of water. Typical Grendel powder charges run between 20-ish and 30-ish grains of powder, depending of course on the powder and bullet choice. These mild charges are not too different from charges used in the .223 or other comparable cartridges. This allows the 6.5 Grendel to propel 100-140 grain bullets up to velocities like 2300 to 2600. These are some pretty general numbers, that obviously are subject to change.
Left to Right: 308 Winchester, 6.5 Grendel, 223 Remington
The odd size of the Grendel case has some other consequences as well. With its .449 bolt-face it falls between the .223 bolts used in most AR-15 rifles and the very common 308 sized bolt-face in larger rifle platforms. Luckily due to popularity of the Grendel and similar cartridges, this has become less of a problem. 7.62×39, .224 Valkyrie and others have made the midsized bolt-face more mainstream.
Additionally, due to its shape and proportions, the Grendel requires a different magazine to feed from AR rifles. There are a few different options out there including followers and complete mag-housings that have been altered to fit the Grendel and its offspring.
My Test Rifle
The rifle featured in this article for testing purposes is a Bear Creek Arsenal bolt-action upper. A handy and cost effective way to convert from one firearms type to another. It features one of their eighteen-inch heavy barrels and threaded 5/8-24 which fits perfect for my suppressor. The 1:8 twist works great with bullets commonly loaded for the Grendel. I used a Maven RS.3 5-30X50 scope which was probably a little more than necessary, but welcome.
Part of the idea behind the Grendel was improved ballistic performance from the AR-15 rifle. With 5.56/.223 chambered rifles, most were shooting bullets from 55grains up to 75-80 grains. Which can be very useful for a great many things, but at 800 yards they have significantly deteriorated performance. That is where the Grendel comes in, even with a light for caliber bullet like a 123 grain 6.5, the Grendel far exceeds even the heavy .224 bullets. For comparison, a couple loads shown below; an average and heavy 5.56 load compared to an average and heavy Grendel load.
Load Data
Velocity/Energy @400yds
Velocity/Energy @800yds
5.56 55gr FMJ 3250 FPS
1800fps/395lbs
1000fps/120lbs
5.56 75gr BTHP 2910 FPS
2025fps/680lbs
1340fps/300lbs
6.5 Grendel 123gr 2450 FPS
1875fps/965lbs
1380fps/520lbs
6.5 Grendel 140gr 2330 FPS
1880fps/1100lbs
1475fps/680lbs
The Grendel loads can have thirty percent or more energy at further distances, which could be vital when incapacitating a target. While velocities are comparable, the energy of the heavier bullets carries further, and better.
Making brass for the little Grendel has come a long way from forming your own from something else. Whether it be Hornady or Starline, you can get some great brass for the Grendel. You can even get Lapua 6.5 Grendel cases now, so you know its serious.
We live in an interesting time, never before has there been so many options for firearms enthusiasts. And at the very same time there is a breathtaking assault against the right to obtain and bear all these arms. Todays subject might appear up front to be a step backwards in firearm design, but it for sure is a step towards countering the assault against second amendment rights for some. Today I present to you the Bear Creek Arsenal BC-15 Bolt-Action rifle. Your eyes aren’t fooling you, this is indeed a bolt-action AR-15 essentially.
That is why I said it might seem like a step backwards in firearm development, but you will soon see what makes this product a good idea.
The Bear Creek Arsenal BC-15 bolt-action rifle
Its appearance as an AR-15 rifle is by design, lets look at the rifle’s features to get started. The lower receiver is in fact a completely normal BCA complete lower, just like every other BCA lower it uses all the same parts interchangeably. (That will come in handy later) Where it differs is the upper receiver, though it also uses a great deal of the same parts there as well.
Edited to add: I enjoyed this rifle so much, that I ordered a second upper. This time an eighteen-inch heavy-barreled 6.5 Grendel. I wanted to have options, as well as another capable rifle for larger purposes. The Grendel upper shares much of the same features, but obviously runs on different magazines.
The Curious Bolt Design
The semi-auto bolt-carrier has been replaced by a different carrier, similar to the semi except missing the rear-most part. This results in the carrier having a fork-like back end. The bolt itself appears to be a standard AR bolt, with no gas rings installed. It rides in the bolt carrier secured by a regular cam-pin, but there is no cam-path cut into the carrier. The resulting motion looks like this; as the bolt handle is pushed forward, the bolt engages the barrel extension the same way it would in a semi-auto, but it rotates and goes into battery when the bolt-handle is pushed down.
Bolt Operation
The operation feels weird for several reasons, first off; the buffer in the stock applies spring tension on the bolt when pulled fully to the rear. This spring pressure is only felt about halfway forward from the extreme rear of the bolt stroke. Secondly; there is another spring behind the bolt inside the carrier. It keeps the bolt all the way forward when pushing into battery, but it also causes some back pressure when chambering a round. And a springs the bolt handle back when it is lifted out of battery.
one down side to the design is that you can’t field-strip the rifle without tools
At first it is quite awkward, and not what you are expecting. However, once you get the hang of it, it is actually quite fast. The opposing forces from the bolt-spring and the buffer spring actually seem to help you run the bolt faster. Once you get over it, its no bother at all.
The Barrel
From the barrel extension forward, as best as I can tell it is 100% the same barrel used in other comparable rifles. Which makes sense from a manufacturers perspective. Since no gas-block is needed, they simply installed a ring over the gas-block perch to prevent gas from blowing out the gas hole. The barrel is truly free-floated in that nothing touches it forward of the barrel nut.
The muzzle is threaded 1/2-28 like most 5.56 barrels, and it came with BCA’s typical muzzle device. I would be changing it out for my Yankee Hill Machine Turbo T3 suppressor almost immediately.
When shooting the 6.5 Grendel upper, I used my Banish Meateater suppressor. It was very pleasant shooting the Grendel with this suppressor.
The Rest
Everything else seemed pretty typical Bear Creek parts, the handguard used on all their AR’s, the lower parts and buttstock all look and function just like you’d expect them to. I’ll give them points on their pistol grip, I do like it much better than most typical grips. They also put one of those accuracy wedge pieces of polymer in it to keep the upper and lower from wobbling.
Other Models and Calibers
Bear Creek also makes these options in other calibers, and you guessed it they also make it in a large frame configuration as well. The options are actually pretty impressive, you can get either Parkerized barrels or 416 Stainless. There are also a great variety of barrel lengths you can choose from, as short as 7-inches and up to 22-inches. And perhaps too many chamberings to mention but I’ll try:
BC-15 Bolt-Action Calibers
BC-10 Bolt-Action Calibers
5.56 Nato
.243 Winchester
.223 Wylde
6.5 Creedmoor
.224 Valkyrie
.308 Winchester
.300 Blackout
8.6 Blackout
6mm ARC
6.5 Grendel
7.62×39 Soviet
350 legend
450 Bushmaster
458 SOCOM
12.7×42 (50 Beowulf)
Shooting the BCA BC-15 Bolt Action
To properly give this rifle a test, I took it across the state to ensure it got to see some country. Initial testing was done in the desert south west, coyote and jack rabbit country. Unfortunately neither of them showed up for the test, but the rifle worked great.
Ergonomics
I will say for sure that it took a little bit to get used to the bolt-throw on this rifle. It is unlike any other bolt-action I’ve ever operated, the lift is very short and the stroke has various degrees of resistance. It took me a minute to figure out what I was doing wrong, but once I got a feel for the operation it became second nature and particularly fast. The buffer spring pressure almost helps you transition from rearward motion to forward by adding spring pressure.
I did notice with the second upper in 6.5 Grendel the bolt was a little more finicky. I am not sure that this had anything to do with the cartridge difference or bolt-face change. Or if it was simply a side effect of mass-produced parts and tolerances.
The rest of this rifle is 100% pure AR, so you already know what that feels like. The trigger that came in the rifle was nothing to write home about but it did not keep the rifle from shooting well. I like the rubberized BCA pistol grip, it gives great purchase and is quite comfortable. The butt stock on the other hand could have come from a CAR-15 airsoft clone, or perhaps even a Nerf gun, but it worked just fine.
the BC-15 Bolt-Action would serve well as a hunting rifle
Reliability
As is typical with bolt-action rifles this one was 100% reliable. The only issues I had were part of the learning process with operation the bolt properly, as well as some ammunition that was a touch long for the chamber.
The rifle cycled cartridges flawlessly, and tossed them out in a neat pile. Feeding from P-Mags is one of the appealing features of this rifle, and it worked great. I was a bit irritated with the AR bolt catch that would lock the bolt up when the last round was fired, but I should have anticipated it.
None of the previous aspects really surprised me, but I was a bit impressed when I put the rifle on paper at 100 yards. With cheap ball ammo the rifle would shoot groups averaging slightly over 1 MOA, and when using PMC Match 77 grain it would print five-shot groups around .6 MOA quite reliably. I guess I shouldn’t be surprised that modern manufacturing processes can produce 1/2 MOA guns that shoot that well for less than $450. I look forward to trying some additional handload options to see if I can get it to shoot even better.
The Grendel, while still shooting sub-MOA deserves a little more attention. I intend to keep tuning handloads to find one that shoots even better. I expect I should be able to shoot 1/2 MOA groups with it as well.
some of the .223/5.56 accuracy resultsAnother example, this time of the Grendel grouping
Value
I did a quick and simple glance over the 223 bolt-action rifles for sale at Sportsmans Warehouse. And of the fifty plus options available there, only half a dozen of them were in the same price range as this rifle. I’ve shot some of those rifles and they didn’t print groups like this as easily.
The great shooting performance of the BC-15 Bolt-Action rifle means it could serve well as a varmint rifle, target shooting or any other similar activity. And because it is essentially an AR-15 there is no shortage of ways to improve it, which takes me to the next subject.
the push of a couple pins allows you to swap from one upper to another
My working theory is two-fold; this rifle being a bolt-action type, there are far less likely to be laws infringing on the right to keep and bear it. So for folks who live behind enemy lines in shit-hole states like California or Maryland, they can finally join the ranks of AR-15 owners, even if they have to cycle the action by hand. And I suppose they can pick fights with the pump-action Ak guys.
The second part of my theory is that buying this “bolt-action” rifle in restricted states, is a perfectly legitimate reason to have a completely functional and uninhibited AR-15 lower receiver. And with the push of a couple pins you can enjoy the same liberties as free men everywhere.
shooting groups for accuracy analysis at 100 yards
Pros and Cons
The popularity of the AR-15 family of rifles has brought the prices down, and since this rifle borrows so much from the AR family, it too has benefitted. Having a great many parts and accessories interchangeable is a great asset, and allows you to set this rifle up however you see fit.
testing my 6.5 Grendel handloads
While it may take a minute to get used to, the rifle works quite well. And its performance on the range was refreshingly positive. Reliable function paired with the incredible compatibility makes it both fun and versatile. Because the rifle shoots better than I had anticipated, I’m actually considering putting a better trigger in the rifle. The mil-spec trigger it came with isn’t terrible but could be better, and I’d like to see how much accuracy I can squeeze out of it.
the Kahles 318i was an excellent scope to test this rifle’s potential
Based on price alone, I think this rifle is pretty damn reasonable. But there are few things I’d change if I could; First off is the super cheap butt stock. I understand why they use cheap ones, as lots of folks change them out anyways. I for sure will be changing it something different. There is also a little pet peeve of mine about putting company logos all over the place, like, you could just put it on the receiver and call it a day. But that is of course just a subjective complaint. Honestly I don’t know what else I’d change on this rifle after what I’ve mentioned.
Final Thoughts
Some folks might chuckle at the idea of a bolt-action AR, I’d be lying if I didn’t say I did the same. But the more I thought about it, and especially after shooting this little rifle quite a bit, I can say my mind has been swayed. Not saying I would give up my traditional bolt-guns in favor of this one, just that I can absolutely see the reasoning behind this design, and a value in having it.
The Bear Creek Arsenal BC-15 Bolt-Action rifle gives a pretty impressive performance considering the sum of its parts. Aside from that, it offers gun owners in tyrannical states an option to play in the AR-15 world. And it does all this for a pretty reasonable price attainable by average Americans. I look forward to putting this rifle to good use on some varmints this spring.
Polymer framed pistols are becoming more and more common every day. With so many options how can you tell which one to choose? Today we are going to dive into yet another new striker fired polymer framed gun so you can decide if it fits your needs. Today we are reviewing the Bear Creek Arsenal Grizzly 101 pistol, a 9mm handgun very similar to the popular Glock 17.
Specifications
Color
Black
SKU
CGP101-91917SSWC2POLY
Weight (lbs)
1.430000
Magazine Capacity
17 Round Magazine
Barrel Length
5
Twist
1:16
Barrel Finish
Stainless Steel
Material
416R Stainless Steel
Thread Pitch
Non-Threaded
Caliber
9MM
Flutes
Non-fluted
Gas System
Blow-Back
History
It would seem that BCA has made at least one attempt at a 9mm pistol before. An all metal version that looks very similar to the Grizzly 101. Perhaps that didn’t go the way they wanted it to, because I see no sign of it on their website. If I had to guess, I’d say that a polymer frame turned out to be much more profitable and perhaps easier to make.
BCA seems to catch a lot of negative attention from the public, at least if you believe what you read on social media and internet forums. I might be lucky, as the only experience I have had with BCA has been a positive one. You can read about the BCA BC-8 Huntmaster here. The Grizzly is only my second exposure to a BCA firearm, and I’m glad you can come along to see how it goes.
Features
Bear Creek Arsenal is known for manufacturing a variety of AR type rifles in assorted different calibers and configurations. The Grizzly is a departure from what BCA commonly manufactures, this could be a good or bad thing depending on your perspective.
The Grizzly is built on a polymer frame similar in size as I mentioned to the Glock 17. This is a great idea as it allows the Grizzly to use many of the Glock 17’s support products, like magazines, and other accessories.
In addition to the commonality, there are some things that set the Grizzly apart from the gun that it appears to emulate. Some cuts to the slide expose the stainless steel barrel, and the slide comes pre-cut for RMR type red dots. Something I would be sure to look into.
Some pretty standard green sights round out the top of the slide which are perfectly useful. If we turn our attention to the frame, you’ll find there is a nice texture molded into the grip. As well as some finger shelves alongside the top of the trigger guard.
No safety other than the trigger blade safety, which is fine by me. A nice undercut where the guard meets the grip makes the pistol comfortable in the hand. And the 17-round magazines are made by KCI.
Other models
The Grizzly 101 is available in a couple different options, mainly different barrel configurations. There are both threaded and unthreaded versions of the pistol. And you can select a couple different titanium nitrided colors of gold, copper and black. I’m no fortune teller, but I’d bet there are other options in the works that will also soon be available.
Bear Creek Arsenal Grizzly 101 Pistol review
Before shooting the Grizzly, I wanted to install a Trijicon RMR. It was easy enough and fit perfectly. Some red dots have a cutout to allow the use of the iron sights, the RMR sits high enough that you can almost see the iron sights but not quite. But with the RMR installed I was ready to hit the range.
I’d brought a couple boxes of ammo from Federal and AAC, and MWLP Trailforger. All were 115 grain FMJ. I started stuffing them into magazines in preparation, loading 17-rounds into the KCI magazines.
Shootability
My very first impressions of shooting the Grizzly were that it seemed a touch spicier than I expected. It’s a full size 9mm pistol, so I expected it to be fairly mild. I also noticed rather quickly that the grip seems a little more square than others. Some folks may find that preferable, but for me it felt just a touch less comfortable.
The Grizzly texture is definitely helpful in getting a good grip on the pistol. And I really like the two finger shelves above the trigger, it allows your thumbs a place to engage. The trigger feels like a striker pistol, I don’t mean that as a bad thing either, it feels just like every other similar gun I’ve used. Reloads were easy using the slide release, I often feel a great variation between different Glock type pistols. I was happy to see this one was easy to feel and press.
The Grizzly green sights were perfectly suitable, but the Trijicon RMR was more my style.
Reliability
During the course of my shooting, the closest thing to a malfunction I experienced was a failure to lock back. It seemed to follow the magazines, so I think it’s fair to put the blame there. I also used a Fab Defense 18-round magazine, which worked flawlessly. I was also able to shoot the Grizzly with a Glock magazine that also worked great.
Other than that the pistol chugged along through everything I threw at it.
Extraction and ejection were just as I’d expect, throwing spent cases clear. The controls were all smooth and never skipped a beat.
Ergonomics
I mentioned the square-ish feeling grip, which might just be my preference showing through. Other than that the gun felt very comfortable in my hand. The undercut trigger guard kept your fingers comfortable while gripping, and the angle of the grip was familiar and pointed well.
The Grizzly has a very similar profile to the Glock 17, but it wouldn’t fit proper in any of my Safariland Glock 17 holsters. So there must be enough difference to matter, though I expect it is likely due to the slide cuts.
Accuracy
Accuracy from the Grizzly was also as I expected, I guess it should come as no surprise that a Glock clone shoots like a Glock. Particularly when shooting with the RMR installed it was pretty easy to keep shots on target. At 10 yards groups would average between 2-4 inches depending on cadence and ammo. To put it bluntly, I felt just as accurate with this gun as with any other G17 styled pistol.
Value
Despite being a pretty close copy of the Glock, I was quite surprised by the low price of this pistol. But as I mentioned at the top, copies of these popular pistols are becoming more and more popular. So I shouldn’t be surprised that the cost keeps coming down.
The Grizzly is listed for $295.00 on the Bear Creek website, which is a pretty agreeable price. Obviously this pistol is priced there for a reason, and you can tell by looking at the gun that it is going to cost less than its cousins. What I mean by that is there are some features on the gun that suggest a less refined process. For example, the stainless steel barrel functions flawlessly but also appears slightly unfinished. Non-chamfered edges on the muzzle look just a tad raw for my taste. The conspicuous BEAR CREEK ARSENAL down the side is a little over the top for me as well, the logo alone should be enough. The machining and molding look good, and to be honest I’m surprised you can make any money on a gun at this price point.
I guess that means I think this gun is a good buy, and if it stands up to round count and use it probably will certainly be a good buy. Time will tell.
Compatible with a variety of aftermarket accessories
Optics ready for RMR footprint
Good grip texture
Cons
Inexpensive suggests cheap
Doesn’t fit my safariland holsters
Slightly unfinished look
Report Card
Shootability (B) shoots well but seems to lack some refinement
Reliability (A-) Only malfunctions seemed related to magazine
Accuracy (B) Nothing fancy, does what you need
Ergonomics (B) Feels good, but also feels sort of like a first try
Value (A) If the Grizzly stands up to use, it seems like a great value
Ammunition Preference
The Grizzly didn’t seem to show a preference for any of the ammo I shot through it. Both 115 and 124 grain loads worked great. I usedFederal Premium 115with great results as well as AAC 115 grain ammunition.
Accessory Upgrades
Because it’s already cut for it, I would highly recommend adding a red dot. I used the Trijicon RMR which cost more than the gun itself. So perhaps something a little more comparable in price would be something like the Gideon Alpha red dot. A good weapon light like the Surefire X300 pictured would also make a good companion.
After shooting with the BCA Grizzly 101 for a while now, I can say I definitely like it. I wouldn’t be trading it for any of my other pistols, but it certainly has a home in my collection. I intend on shooting it a lot more, perhaps it can be my loaner pistol. That way I can see how it stacks up over time and higher round count. Follow me to see how that goes.
